LM317 is a famous linear voltage regulator IC. It provides very stable, uniform and smooth output which does not fluctuate with load changes. It can also be used as a precise current limiting device which is essential for testing electronic equipment. Unlike 78xx series, the output voltage of LM317 can be adjusted using a variable resistor or a set of fixed resistors. It has built in short circuit protection as well as thermal overheat protection. LM317 is exceptionally easy to use and requires only two resistors to do basic voltage regulation however more refined output can be achieved using a few more components. No capacitors are needed unless input source is situated far enough from LM317.
LM317 Shape and Pinout
LM317 has 3 pins and a transistor like TO-220 shape which makes it easier to fit on heatsinks. If you grab LM317 upside down while IC’s printed name is facing towards you and it’s pins are on top, then the left pin is the input pin, the center pin is output pin while the right pin is the adjustment pin. Note: The heat exchanger or heatsink plate also acts as an output terminal due to its internal connection with the center pin. I have also added an image to make sure you fully understand the pin numbers for LM317.
LM317 Technical Specifications
LM317 has a wide input range of 4.25 Volts to 40 Volts while the output range is between 1.25 Volts to 37 Volts. The minimum possible difference between the input and output voltage is 3V, anything below that and output may start to fluctuate unpredictably. Maximum possible voltage differential is 40V. With a decent sized heatsink, LM317 can output up to 1.5A (1500mA) of current however you will have to make sure the maximum operating temperature of LM317 doesn’t exceed 125C otherwise it will thermally shutdown or can even get permanently damaged.
Basic Adjustable Voltage Regulator Using LM317
I am adding a circuit diagram of a very basic voltage regulator circuit using LM317 which is extremely simple and it can even be built without a PCB or bread board. You can fit lm317 upside down on a heatsink and solder the resistor directly on the top of its pins. The variable resistor can be connected to the LM317 using wires and can be placed anywhere you want. If you are fitting this circuit inside a box then you should drill a hole on front of your box and place the variable resistor in that hole with a plastic nob outside to adjust the regulated output voltage.
LM317 Output Voltage Calculation Formula
You can also replace variable resistor with a fixed resistor in case you need fixed output voltage. For example, you can get a 5.1V DC output from this circuit if you replace 5K variable resistor with a fixed 680 OHM resistor. You can use following formula to calculate which resistors to use and what output voltage you will you get.
Vout = 1.25 X (1 + (R2 / R1) )
In case of 680 OHM, this is how we calculate expected output voltage
=1.25 X (1 + (680 / 220))
=1.25 X (1+ 3.09)
=1.25 X 4.09
Note: Value of R1 and R2 should be in OHMs
Simple but Precise Current Limiting Circuit
In the image below you can see a very precise yet very simple circuit which limits current to a value determined by R1 resistor. I have found this circuit surprisingly accurate and even comparable to some pretty professional current limiting power supplies. Please note that LM317 itself is pretty accurate however the R1 resistor should be big enough to not heat too much otherwise the heat may result in changing the value of resistance slightly which will result in changing current by a few milliamps.
For example, a 3.9OHM resistor in place or R1 will output approximately 320 milliamperes current regardless of the voltage you set.
You can use following formula to calculate output current.
Output Current = 1.25 / R1
Note: Value of R1 should be in OHMs
Is it Possible to Use LM317 Without a Heatsink Plate?
亲友娄底棋牌有没有挂current limiter circuit
Yes, but just for very light loads and you will also need to monitor the operating temperature of LM317 so that It does not exceed 125C. In my experience, if your application has a heat dissipation of less than 1W then there is a good chance that you can use the IC without a heatsink plate. However please note that continuous use of LM317 near its maximum operating temperature can alter its die and reduce its life span.
If you are planning to use LM317 in your circuit and you have any questions in your mind then please don’t hesitate to post them in the comments section below.